NITRIC OXIDE + OXYGEN
(NO + O2) Analyzer
Cross Duct Multi Gas
GasEye Cross Duct MG NO/O2
in-situ nitric oxide and OXygen analyzer
GasEye NO/O2 is a high performance in-situ nitric oxide and oxygen analyzer. Suitable for safety applications and process control. 24/7 continuous operation. No sample preparation. No zero drift. No field calibration. Low cost of ownership.
Features
- NO ranges: 0 – 50 ppmv to 0 – 50 vol%
- O2 ranges: 0 – 1 vol% to 0 – 100 vol%
- Process temperature: 0 – 550°C
- Real time sensing: response time below 0.1 second
- High selectivity: automatic compensation for interference effect from other constituents in the gas sample
- High sensitivity: detection limits down to ppb range
- In-situ monitoring: direct in the process, no sample preparation
- Maintenance free: equipped with a self-calibrating feature, no field calibration necessary
- Robustness: IP66 enclosure, suitable for outdoor and indoor installations and harsh environments
- Insensitive to dust and smoke in the measured process: up to 50 g/m3
- ATEX version available
Example Applications
- Denitrification (deNOx)
- Process control
- Emission monitoring
Example Industries
- Power industry
- Chemical industry
- Metallurgy industry
Application type
 Measurement conditions |
|
| Process gas temperature: | 0ºC to 550ºC |
| Process gas pressure: | 0.7 – 2 barA |
| Maximum path length: | up to 25 meter |
 Dynamic performance |
|
| Warm-up time: | approx. 5 minutes |
| Minimum response time (T90): | 100 milliseconds |
 Climatic conditions |
|
| Ambient temperature: | -20ºC to +55ºC |
| Ambient pressure: | 800 – 1200 hPa |
| Ambient humidity: | RH < 99%, non-condensing |
 Process Purging (if necessary) |
|
| Purging gas: | instrument air or N2 |
| Process purge flow rates: | 5 – 50 l/min |
| Sensor purge flow rates: | 0.2 – 7 l/min |
Technical specification
 Interfaces |
|
| Outputs: | configurable 4 x analog output, 4 – 20 mA (for example: CO concentration, O2 concentration, process transmission, 1 x process temperature (optional)), easy user selection via DIP switch between active/passive mode |
| 8 x digital output (NAMUR) | |
| Inputs: | configurable 4 x analog input, 4 – 20 mA (for example: process temperature, pressure), easy user selection via DIP switch between active/passive mode |
| 1 x RTD (PT100/PT1000) – easy user selection via DIP switch between PT100/PT1000 and 2-/3-/4-wires | |
| 8 x digital input | |
| Local User Interface: | Human Machine Interface (HMI) – LCD backlight display located on the transmitter housing lid |
| Ethernet port: a) WebServer – system configuration and data acquisition via web browser, b) Windows based program – GasEye logger for real-time data acquisition, c) remote service and diagnostics |
|
| Optional: | Modbus (TCP/IP), Modbus RTU, Profinet, Profibus |
| Electrical Characteristics |
|
| Power input: | 24 VDC nominal (19 – 30 VDC) |
| Power consumption: | < 25 VA (< 35 VA if ATEX) |
| Additional build-in features |
|
| Automatic gain control (AGC): | AGC ensures correct gas measurement even at high dust loads resulting in loss of optical transmission down to 0.5%. AGC operates fully automatic with no need for manual adjustment of the signal gain under any process conditions. |
| Self-calibration features: | Internal reference gas compartment is used for closed loop control of the zero and span drift |
| Download a file: | |
| GasEYE system elements: | preview | download |
| Active analog input: | preview | download |
| Active analog output: | preview | download |
| Passive analog input: | preview | download |
| Passive analog output: | preview | download |
| Isolated Digital Input: | preview | download |
| Isolated Digital Output: | preview | download |
| Power Supply: | preview | download |
| RemoteRX: | preview | download |
| PT100/PT1000 2-wire: | preview | download |
| PT100/PT1000 3-wire: | preview | download |
| PT100/PT1000 4-wire: | preview | download |
| Transmitter |
|
| Dimensions: | width x height: 330 mm x 230 mm, length: 350 mm |
| Weight: | 15 kg |
| Equipment: | 2 x laser sockets, purging fittings |
 Receiver |
|
| Dimensions: | width x height: 160 mm x 160 mm, length: 330 mm |
| Weight: | 13 kg |
| Equipment: | 1 cable gland, purging fittings |
| Central Unit |
|
| Dimensions: | width x height: 330 mm x 230 mm, length: 110 mm |
| Weight: | 5 kg |
| Equipment: | display with status indicators, 6 cable glands, Ethernet socket, purging fittings |
 Materials |
|
| Housings: | RAL 5010 coated aluminum, (optional RAL 7040) |
| Process interface: | stainless steel 316 with quartz window, DN50 PN16 (EN 1092-1), DN65 PN6 with easy to clean window, optional other standards (ANSI, JIS) |
| Purging tubes: | inside diameter: 38 mm, length: 400mm (optional other dimensions), stainless steel 316 (optional PTFE coating) |
| Process gaskets: | reinforced graphite |
| Download a file: | |
| GasEYE Cross Duct units construction elements: | preview | download |
| GasEYE Cross Duct instrument assembly: | preview | download |
| GasEYE Cross Duct cross-section: | preview | download |
| Low Voltage Directive (LVD) 2014/35/EU | PN-EN 61010-1:2011 |
| Laser radiation: Laser Class I product acc. to PN-EN 60825-1:2014-11 | |
| EMC Directive 2014/30/EU | EN 61326-1:2013 |
| RoHS Directive 2011/65/EU | |
| ATEX Directive 2014/34/EU | EN IEC 60079-0:2018 – Explosive atmospheres – Part 0: Equipment – General requirements |
| EN 60079-2:2014 – Explosive atmospheres – Part 2: Equipment protection by pressurized enclosure “p” | |
| EN 60079-26:2015 – Explosive atmospheres – Part 26: Equipment with Equipment Protection Level (EPL) Ga | |
| EN 60079-28:2015 – Explosive atmospheres – Part 28: Protection of equipment and transmission systems using optical radiation | |
|
Explosion protection (standard version):
|
|
|
Explosion protection (optional version):
Certificate No. KDB 20ATEX0003X EN |
|
|
Explosion protection (optional version):
|